0
1.9kviews
Machine Design - 2 : Question Paper May 2015 - Mechanical Engineering (Semester 7) | Mumbai University (MU)
1 Answer
0
2views

Machine Design - 2 - May 2015

Mechanical Engineering (Semester 7)

TOTAL MARKS: 80
TOTAL TIME: 3 HOURS
(1) Question 1 is compulsory.
(2) Attempt any three from the remaining questions.
(3) Assume data if required.
(4) Figures to the right indicate full marks.


Answer any four questions:

1 (a) Write assumption made by Lewis and derive Lewis equation for the bending strength of Gear tooth. (5 marks)


1 (b) Explain the properties of bearing material. (5 marks)


1 (c) Draw the pulley arrangement for six fall system and explain function of Compensating pulley. (5 marks)


1 (d) Explain priming and Cavitation in Centrifugal pump. (5 marks)


1 (e) What change in the loading of a ball bearing will cause the expected life to be doubled. (5 marks)


2 Design a pair of steel Helical gears to transmit 15 KW at 1440 rpm of pinion. The desire transmission ratio is 4:1. Write constructional details with neat sketches. (20 marks)


3 (a) Find the module of the bevel gear and check if for wear load for the following specification.
Power transmitted: 25 KW,
Input Speed: 360 rpm
Reduction Ratio, 3
Angle between shaft: 90°.
(10 marks)


3 (b) A full journal bearing (β=360°) is use for supporting a load of 7KN. Runs at 500 rpm for machine tool application. Select fit H9e9 and Take L/D=1.
Find:
i) Bearing dimensions
ii) Sommerfeld Number,
iii) Minimum oil film thickness,
iv) Coefficient of friction,
v) Rise in temp of oil.
(10 marks)


4 (a) A DGBB having SKF No. 6207 subjected to load cycle as below which is repeated. Find the probability for expected life of 1000 Hrs. Take Service factor, S=1.2.

Phase Radial Load Thrust Load Speed (rpm) %
I 3000 1000 600 15
II 3500 1000 800 20
III 5000 100 900 30
IV 500 2000 1500 35
(15 marks)


4 (b) Discuss advantages and disadvantages of Rolling contact bearing over sliding contact bearing. (5 marks)


6 (a) How to control the pressure angle in Cam. Explain. (4 marks)


6 (b) A Rotary disc cam with central translatery roller follower has following motion. Forward Stroke of 22mm in 100° of cam rotation with SHM motion, dwell of 50° of cam rotation and return stroke of 22mm in 90° of cam rotation with SHM. Remaining dwell to complete the cycle. Mass of the follower is 1.5 Kg and cam shaft speed is 500 rpm. The maximum pressure angle during forward stroke and return is limited to 25°. The external force during forward stroke is 600 N and that of return stroke is 100N. Find cam dimension, roller follower along with pin and spring. (16 marks)


7 (a) Explain the terms NPSH and its significance in Centrifugal Pump. (5 marks)


7 (b) Refer the data given for a Centrifugal Pump.
Manometric Head: 24m
Discharge: 1200LPM
i) Decide diameters of the suction and delivery pipes.
ii) Select the impeller (impeller dia., inlet and outlet vane angles, no. of vanes, width at inlet and outlet),
Design the shape of volute casing.
(15 marks)
5 (a) For the following specification of an EOT Crane, Application - Class II
Load to be Lifted - 140 KN
i) Design a rope of 6×37 type and find its life.
ii) Design the crane hook and find induced stresses at most critical section.
iii) Select suitable single Thrust ball bearing.
iv) Design Cross Piece.
v) Design Shackle plate.
(20 marks)

Please log in to add an answer.