0
1.4kviews
Advanced Microwave Engg : Question Paper May 2014 - Electronics & Telecomm. (Semester 8) | Mumbai University (MU)
1 Answer
0
3views

Advanced Microwave Engg - May 2014

Electronics & Telecomm. (Semester 8)

TOTAL MARKS: 100
TOTAL TIME: 3 HOURS
(1) Question 1 is compulsory.
(2) Attempt any four from the remaining questions.
(3) Assume data wherever required.
(4) Figures to the right indicate full marks.
1(a) Define signal to noise ration and noise figure with help of a noisy network. Explain test set up to measure signal to noise ratio.(5 marks) 1(b) Prove that scattering matrix is symmetrical and reciprocal.(5 marks) 1(c) Explain unilateral figure of merit.(5 marks) 1(d) Explain the terms conversion loss and Isolation with reference to mixer.(5 marks) 2(a) Consider two power BJT amplifiers used in circuit configuration shown below having following specification:

Amplifier Go(dB)Gi(dB) PidB(dBm)
1 8 727
2 10922

Assume that operating frequency is 1 Ghz and input power is 5.5 dBm. Specify correct BJT amplifiers that must be used at each stage to obtain 29.5 dBm output power. Assume each two way divider/combiner has 0.5 dB insertion loss.(10 marks) 2(b) Discuss amplifier linearisation methods.(10 marks) 3(a) For an ideal transformer with turns ratio n=n1/n2 prove that the scattering matrix is $$ S= \begin{bmatrix}\frac {n^2-1}{n^2+1} & \frac {2n}{n^2 +1} \\ \frac {2n}{n^2+1} & \frac {1-n^2}{n^2+1} \end{bmatrix} $$ (10 marks) 3(b) Define and explain noise correlation matrix for general noisy two port network. What is congruence transformation?(10 marks) 4 Design a transistor oscillator at 6GHz using an FET in CS configuration driving a 50Ω load on drain side. The S-parameters at 50 Ω are $$ S= \begin{bmatrix} 0.9 \angle 150 &0.2 \angle -15 \\ 2.6 \angle 50 & 0.5 \angle 105 \end{bmatrix} $$ Calculate and plot output stability circle for $$|\Gamma_{IN}| >> 1. \ Choose \ \Gamma_T \ so \ that \ |\Gamma_{IN}|>>1 $$ Design load and terminating networks. (20 marks) 5 (a) Discuss various mixer topologies. Compare performance of various topologies.(10 marks) 5 (b) Discuss generalised single ended mixer design approach. Give design consideration.(10 marks) 6 (a) For a two port network the ABCD matrix is given as: $$ \begin{bmatrix} A &B \\C &D \end{bmatrix}= \begin{bmatrix}0.5 &j1.6 \\j1.6 &0.5 \end{bmatrix} $$ Find scattering matrix if Zo=50 Ω. Find condition of reciprocity. (10 marks) 6 (b) Discuss generator tuning networks for microwave oscillators.(10 marks) 7 (a) A GaAs FET is biased for minimum noise figure and has following S parameters and noise parameter at 4 Ghz (Zo=50 Ω). $$ S= \begin{bmatrix}0.6 \angle -60 &0.05 \angle 26 \\ 1.9 \angle 81 & 0.5 \angle -60 \end{bmatrix} \\ F\min =1.6 dB \ \Gamma_{opt}=0.62 \angle 100 \ R_N=20 \Omega $$ Design an amplifier with 2dB noise figure and maximum gain compatible with this noise figure. Assume device is unilateral (15 marks) 7 (b) Consider the amplifier circuit shown below. The input and output matching network are to be designed using open circuited stubs for ΓS=0.5 ∠120 and ΓL=0.4∠90. User Smith Chart. (5 marks)

Please log in to add an answer.