0
Analog Electronics - 1 : Question Paper Dec 2014 - Electronics & Telecomm (Semester 3) | Mumbai University (MU)

Analog Electronics - 1 - Dec 2014

Electronics & Telecomm. (Semester 3)

TOTAL MARKS: 80
TOTAL TIME: 3 HOURS
(1) Question 1 is compulsory.
(2) Attempt any three from the remaining questions.
(3) Assume data if required.
(4) Figures to the right indicate full marks.


Attempt any five:

1 (a) The PNP transistor shown in Fig a has ?=50. Find the value of Rc to obtain Vc=+5V. What happens if transistor is replaced with another having ?=100. (5 marks) 1 (b) Draw small signal model of JFET and explain significance of each parameter.(5 marks) 1 (c) Why common collector amplifier is used as buffer. Why buffers are required.(5 marks) 1 (d) Write down current equation of diode and explain significance of each parameters.(5 marks) 1 (e) For the circuit shown in Fig le. Find IDS and VDS if VRS=1.5V. (5 marks) 1 (f) Compare Collpit's and Clapp's oscillator.(5 marks) 2 (a) Explain working of n-channel eMOSFET with the help output characteristics, showing clearly effect of channel length modulation. Give equation of drain current in linear and saturation current along with conditions.(10 marks) 2 (b) Design JFET circuit with voltage divider biasing as shown in Fig 2b with JFET parameters IDSS=12mA, VF=3.5V and ?=0. Let R1+R2=100K, IDSQ=5mA. And VDSQ=5V. (10 marks) 3 (a) Draw circuit diagram of common emitter amplifier with voltage divider bias with bypassed emitter resistance and derive expression for voltage gain, current gain, input resistance, output resistance using hybrid-?- model which includes early effect.(10 marks) 3 (b) In n-channel E-MOSFET
i) Substrate doping NA=1016 cm-3.
ii) Poly=silicon Gae doping ND=1020cm-3
iii) Gate oxide thickness tox=0.5 ?m
iv) Oxide positive charge interface density=4&time;1010 cm-2
v) Charge of electron=1.6×10-19 col
vi) Permittivity of free space &insin;0=8.85&time;10-14 F/cm.
vii) Dielectric constant of Si=11.9

viii) Dielectric constant of Si02=3.9
Find zero bias threshold voltage (VTO)
(10 marks)
4 (a) Explain the working of Wien-Bridge Oscillator. Derive the expression for frequency of Oscillation and the value of gain required for sustained oscillation.(10 marks) 4 (b) For the circuit shown i Fig 4b, assume ?=100. i) Find Thevenin's equivalent voltage VTH and resistance RTH for base circuit ii) Determine ICQ and VCEQ (10 marks) 5 (a) Draw a required diode clamper circuit to generate the output VD to from the input Vt as shown in Fig 5a if ii) V?=0.7V. Where V? is cut-in voltage of diode. (10 marks) 5 (b) What are different biasing techniques used to bias D-MOSFET and E-MOSFET. Explain with the help of appropriate circuit diagrams.(10 marks) 6 (a) Hybrid-? model of BJT(5 marks) 6 (b) Twin-T oscillator(5 marks) 6 (c) AC and DC load line(5 marks) 6 (d) MOS capacitor.(5 marks)

0  upvotes

Next up

Read More Questions

If you are looking for answer to specific questions, you can search them here. We'll find the best answer for you.

Search

Study Full Subject

If you are looking for good study material, you can checkout our subjects. Hundreds of important topics are covered in them.

Know More