0
612views
Engineering Graphics Question Paper - December 2015 - First Year Engineering (Set A) (Semester 1) - Rajiv Gandhi Proudyogiki Vishwavidyalaya (RGPV)
1 Answer
0
7views

Engineering Graphics - December 2015

RGPV First Year Engineering (Set A) (Semester 1)

Total marks: --
Total time: --
INSTRUCTIONS
(1) Assume appropriate data and state your reasons
(2) Marks are given to the right of every question
(3) Draw neat diagrams wherever necessary
1(a) Explain the principle of diagonal. 2 marks

1(b) What are the uses of involute and spiral curve? 2 marks

1(c) Draw the Locus of a point equidistant from a given point and a fixed straight line. 3 marks

Solve any one question from Q.1(d) &Q.1(e)

1(d) Draw a rectangle 50mm and 75 mm side. Draw an ellipse circumscribes the rectangle. 7 marks

1(e) A stick AB, 12cm long rotates about fixed end A at constant angular velocity of π/6 rad/sec. A point p moves along the stick from A to B with velocity 0.5 cm/sec. Draw a curve traced by point p when it moves from s position 3 cm away from point A to end B. Draw Tangent and normal to the curve when p is at the middle of the stick AB, name the curve. 7marks

2(a) Define H.T. and V.T. related to projection of lines. 2 marks

2(b) Compare the first angle and third angle projection method.Describe your answer by giving suitable illustrations. 2 marks

2(c) A point is 50 mm below H.P. in third quadrant and its shortest distance from XY line is 65mm. Draw its fromt and top view. 3 marks

Solve any one question from Q.2(d) &Q.2(e)

2(d) The end p of a line PQ is 120 mm long is 30 mm above H.P. and 60 mm behind V.P. The line is inclined at an angle of 30° with the reference planes of projection. The point Q is beloq the H.P. Draw the projections of the line PQ and locate the point Q. 7 marks

2(e) A line AB 120 mm long is inclined at 45° to H.P. and 30° to V.P. The end A is in the second quadrant and end B is in fourth Quadrant. A point C in AB 40 mm from A. In both the planes. Draw projection of AB. 7 marks

3(a) Explain H.T. and V.T. related to projection of planes. 2 marks

3(b) Show by means of traces each of the following planes.
i) Perpendicular to H.P. and V.P.
ii) Parallel to and 40 mm away from V.P.
2 marks

3(c) An equilateral Triangle of 5 am side has its V.T. parallel to and 2.5 am above xy line, It has no H.T. Draw its projection when one of its side is inclined st 45° to the V.P. 3 marks

Solve any one question from Q.3(d) &Q.3(e)

3(d) A square prism, with the side of its base 40mm and Axis 70 mm long is Lying on one of its base edges on the H.P. in Such a way that this base edge makes an angle of 45° with V.P. and the Axis is inclined at 30° to the H.P. Draw projection of solid using Auxiliary plane method. 7 marks

3(e) Draw the projection of a cube of 25 mm long edges resting on H.P. on one of its corners with a solid diagonal perpendicular to V.P. 7 marks

4(a) What are the different positions of section plane with reference ro principal planes? 2 marks

4(b) What is the Importance of section and intersection of solids? 2 marks

4(c) Explain with diagram the difference between the parallel and radial line development method for solids. 3 marks

Solve any one question from Q.4(d) &Q.4(e)

4(d) A vertical cylinder of 80 mm diameter is completely penetrated by another cylinder of 60 mm diameter, their axis bisecting each other at right angles. Draw their projection showing curve of penetration assuming the axis of penetrating cylinder to be parallel to V.P. 7 marks

4(e) A cone diameter of base 60 mm and axis 70 mm long is resting on its base on the H.P. It is cut by an A.I.P. So that the true shape of the section is an isosceles triangle having 50 mm base. Draw the plane, the elevation and true shape of the section. 7 marks

5(a) What is the difference between Isometric view and Isometric projection? 2 marks

5(b) Draw a Isometric scale. 2 marks

5(c) Write the difference between solid and surface modelling. What are the limitations of CAD? 3 marks

Solve any one question from Q.5(d) &Q.5(e)

5(d) Draw the Isometric projection of a 50 mm diameter sphere resting centrally on the top of a cylindrical block of base 60 mm diameter and height 90 mm. 7 marks

5(e) Draw the isometric projection of a cube of side 50 mm resting centrally on the top of a Cylindrical Block of base 60 mm and height 80 mm. 7 marks

Please log in to add an answer.