1
15kviews
Numericals on Cam Mechanism
1 Answer
2
293views

Q.1 A cam is to give the following motion to a knife-edged follower :

1. Outstroke during 60° of cam rotation ;

2. Dwell for the next 30° of cam rotation ;

3. Return stroke during next 60° of cam rotation, and

4. Dwell for the remaining 210° of cam rotation.

The stroke of the follower is 40 mm and the minimum radius of the cam is 50 mm. The follower moves with uniform velocity during both the outstroke and return strokes. Draw the profile of the cam when (a) the axis of the follower passes through the axis of the cam shaft, and (b) the axis of the follower is offset by 20 mm from the axis of the cam shaft.

enter image description here

First of all, the displacement diagram, as shown in Fig. 20.10, is drawn as discussed in the following steps :

1. Draw a horizontal line $AX = 360°$ to some suitable scale. On this line, mark $AS = 60°$ to represent outstroke of the follower, $ST = 30°$ to represent dwell, $TP = 60°$ to represent return stroke and $PX = 210°$ to represent dwell.

2. Draw vertical line $AY$ equal to the stroke of the follower (i.e. 40 mm) and complete the rectangle as shown in Fig. 20.10.

3. Divide the angular displacement during outstroke and return stroke into any equal number of even parts (say six) and draw vertical lines through each point.

4. Since the follower moves with uniform velocity during outstroke and return stroke, therefore the displacement diagram consists of straight lines. Join AG and HP.

5. The complete displacement diagram is shown by $AGHPX$ in Fig. 20.10.

(a) Profile of the cam when the axis of follower passes through the axis of cam shaft

The profile of the cam when the axis of the follower passes through the axis of the cam shaft, as shown in Fig. 20.11, is drawn as discussed in the following steps :

enter image description here

1. Draw a base circle with radius equal to the minimum radius of the cam (i.e. 50 mm) with O as centre.

2. Since the axis of the follower passes through the axis of the cam shaft, therefore mark trace point A, as shown in Fig. 20.11.

3. From $OA$, mark angle $AOS = 60°$ to represent outstroke, angle $SOT = 30°$ to represent dwell and angle $TOP = 60°$ to represent return stroke.

4. Divide the angular displacements during outstroke and return stroke (i.e. angle$AOS$ and angle $TOP$) into the same number of equal even parts as in displacement diagram.

5. Join the points $1, 2, 3 ...$etc. and $0’,1’, 2’, 3’, ...$ etc. with centre O and produce beyond the base circle as shown in Fig. 20.11.

6. Now set off $1B, 2C, 3D ...$ etc. and $0,H,1’,J ...$ etc. from the displacement diagram.

7. Join the points $A, B, C,... M, N, P$ with a smooth curve. The curve $AGHPA$ is the complete profile of the cam.

Notes : The points B, C, D .... L, M, N may also be obtained as follows :

1. Mark $AY = 40$ mm on the axis of the follower, and set of $Ab, Ac, Ad...$ etc. equal to the distances $1B, 2C, 3D...$ etc. as in displacement diagram.

2. From the centre of the cam O, draw arcs with radii Ob, Oc, Od etc. The arcs intersect the produced lines $O1, O2...$ etc. at $B, C, D ... L, M, N$.

(b) Profile of the cam when the axis of the follower is offset by 20 mm from the axis of the cam shaft The profile of the cam when the axis of the follower is offset from the axis of the cam shaft, as shown in Fig. 20.12, is drawn as discussed in the following steps :

enter image description here

1.strong text Draw a base circle with radius equal to the minimum radius of the cam (i.e. 50 mm) with O as centre.

2. Draw the axis of the follower at a distance of 20 mm from the axis of the cam, which intersects the base circle at A.

3. Join $AO$ and draw an offset circle of radius 20 mm with centre O.

4. From $OA$, mark angle $AOS = 60°$ to represent outstroke, angle $SOT = 30°$ to represent dwell and angle $TOP = 60°$ to represent return stroke.

5. Divide the angular displacement during outstroke and return stroke (i.e. angle $AOS$ and angle $TOP$) into the same number of equal even parts as in displacement diagram.

6. Now from the points $1, 2, 3 ...$ etc. and $0’,1’, 2’,3’...$ etc. on the base circle, draw tangents to the offset circle and produce these tangents beyond the base circle as shown in Fig.20.12.

7. Now set off $1B, 2C, 3D ...$ etc. and $0’H,1’J ...$ etc. from the displacement diagram.

8. Join the points $A, B, C ...M, N, P$ with a smooth curve. The curve $AGHPA$ is the complete profile of the cam.


Q.2 A cam is to be designed for a knife edge follower with the following data :

1. Cam lift = 40 mm during 90° of cam rotation with simple harmonic motion. 2. Dwell for the next 30°. 3. During the next 60° of cam rotation, the follower returns to its original position with simple harmonic motion. 4. Dwell during the remaining 180°.

Draw the profile of the cam when

(a) the line of stroke of the follower passes through the axis of the cam shaft, and

(b) the line of stroke is offset 20 mm from the axis of the cam shaft. The radius of the base circle of the cam is 40 mm. Determine the maximum velocity and acceleration of the follower during its ascent and descent, if the cam rotates at 240 r.p.m.

Solution.

Given : S = 40 mm = 0.04 m; $\theta_0 = 90° = \frac{\pi}{2} rad = 1.571 rad$ ; $\theta_R= 60° = \frac{\pi}{3} rad = 1.047 rad$ ; N = 240 r.p.m.

enter image description here

Fig 20.13

First of all, the displacement diagram, as shown in Fig 20.13, is drawn as discussed in the following steps :

  1. Draw horizontal line $AX = 360°$ to some suitable scale. On this line, mark $AS = 90°$ to represent out stroke ; $SR = 30°$ to represent dwell ; $RP = 60°$ to represent return stroke and $PX = 180°$ to represent dwell.

  2. Draw vertical line $AY = 40$ mm to represent the cam lift or stroke of the follower and complete the rectangle as shown in Fig. 20.13.

  3. Divide the angular displacement during out stroke and return stroke into any equal number of even parts (say six) and draw vertical lines through each point.

  4. Since the follower moves with simple harmonic motion, therefore draw a semicircle with AY as diameter and divide into six equal parts.

  5. From points $a, b, c ...$ etc. draw horizontal lines intersecting the vertical lines drawn through $1, 2, 3 ...$ etc. and $0’,1’, 2’...$ etc. at $B, C, D ... M, N, P$.

  6. Join the points $A, B, C ...$ etc. with a smooth curve as shown in Fig. 20.13. This is the required displacement diagram.

(a) Profile of the cam when the line of stroke of the follower passes through the axis of the cam shaft

The profile of the cam when the line of stroke of the follower passes through the axis of the cam shaft, as shown in Fig. 20.14, is drawn in the similar way as is discussed in Example 20.1.

enter image description here

Fig. 20.14

b) Profile of the cam when the line of stroke of the follower is offset 20 mm from the axis of the cam shaft

The profile of the cam when the line of stroke of the follower is offset 20 mm from the axis of the cam shaft, as shown in Fig. 20.15, is drawn in the similar way as discussed in Example 20.1.

enter image description here

Maximum velocity of the follower during its ascent and descent

We know that angular velocity of the cam,

$\omega=\frac{2\pi N}{60}=\frac{2\pi*240}{60}=25.14$rad/s

We also know that the maximum velocity of the follower during its ascent,

$V_0=\frac{\pi \omega s}{2\theta_0}=\frac{\pi*25.14*0.04}{2*1.571}=1$m/s.......(Ans)

and maximum velocity of the follower during its descent,

$V_R=\frac{\pi \omega s}{2\theta_R}=\frac{\pi*25.14*0.04}{2*1.047}=1.51m/s$..........(Ans)

Maximum acceleration of the follower during its ascent and descent

$a_0=\frac{\pi^2 \omega^2 s}{2(\theta_0)^2}=\frac{\pi^2*(25.14)^2*0.04}{2*(1.571)^2}=50.6$ $m/s^2$.........(Ans)

We know that the maximum acceleration of the follower during its ascent,

$a_R=\frac{\pi^2 \omega^2 s}{2(\theta_R)^2}=\frac{\pi^2*(25.14)^2*0.04}{2*(1.047)^2}=113.8$ $m/s^2$ ......(Ans)

Please log in to add an answer.