Ask
Login
TAGGED IN

Advanced Geotechnical Engineering

Follow this tag to get notifications whenever a new post is added

ALL TAGS
3
votes
0
answers
2.2k
views
0
answers
A 5 m deep canal has side slope of 1:1. The properties of soil are c = 20 kN/m$^{2}$, $\phi_{u}=10^{\circ}$, e=0.8 and G=2.8.
advanced geotechnical engineering updated 4.7 years ago by teamques10 ★ 69k
2
votes
0
answers
1.6k
views
0
answers
Describe briefly Culmann's graphical method for determining total active earth pressure also draw the change in Culmann's curve when there is a line load acting on backfill.
advanced geotechnical engineering updated 3.6 years ago by teamques10 ★ 69k
0
votes
0
answers
344
views
0
answers
Lateral Load Pile Calculation
advanced geotechnical engineering updated 2.7 years ago by Chandan15 • 300
2
votes
0
answers
722
views
0
answers
Explain in detail the effect of water table on ultimate bearing capacity of shallow foundations.
advanced geotechnical engineering updated 3.6 years ago by teamques10 ★ 69k
2
votes
0
answers
673
views
0
answers
Explain the type of piles based on mechanism of load transfer.
advanced geotechnical engineering updated 3.6 years ago by teamques10 ★ 69k
2
votes
0
answers
802
views
0
answers
Describe pile load test for calculating allowable load of single pile as IS 2911 Part 4.
advanced geotechnical engineering updated 3.6 years ago by teamques10 ★ 69k
2
votes
0
answers
939
views
0
answers
For the sheet pile wall shown in figure find the depth of embedment:
advanced geotechnical engineering updated 4.7 years ago by teamques10 ★ 69k
2
votes
0
answers
2.0k
views
0
answers
Explain the primary consolidation by spring analogy system?
advanced geotechnical engineering updated 3.6 years ago by teamques10 ★ 69k
3
votes
0
answers
3.6k
views
0
answers
Explain briefly Rebhan's graphical method for finding active earth pressure.
advanced geotechnical engineering updated 3.6 years ago by teamques10 ★ 69k
1
vote
0
answers
1.6k
views
0
answers
A retaining wall 8m high retains sand with $\phi=30^{\circ}$ and $\gamma=24kN/m^{2}$ upto a depth of 4m from the top.
advanced geotechnical engineering updated 4.7 years ago by teamques10 ★ 69k
2
votes
0
answers
772
views
0
answers
Briefly explain different stability checks gravity retaining wall by showing minimum values of factor of safety.
advanced geotechnical engineering updated 3.6 years ago by teamques10 ★ 69k
3
votes
0
answers
2.0k
views
0
answers
Elaborate the uses of Taylor's stability number in slope stability analysis.
advanced geotechnical engineering updated 3.6 years ago by teamques10 ★ 69k
3
votes
0
answers
1.2k
views
0
answers
Explain the direct and indirect method of soil investigation.
advanced geotechnical engineering updated 3.6 years ago by teamques10 ★ 69k
2
votes
0
answers
1.2k
views
0
answers
A cut has to be made 12m deep, inclined at an angle of 35$^{\circ}$ to the horizontal.
advanced geotechnical engineering updated 3.6 years ago by teamques10 ★ 69k
0
votes
0
answers
1.7k
views
0
answers
A retaining wall, 3m high supports a dry cohesionless backfill with a plane ground surface sloping upwards at a surcharge angle of 10$^{\circ}$ from top of the wall.
advanced geotechnical engineering updated 4.7 years ago by teamques10 ★ 69k
0
votes
0
answers
1.2k
views
0
answers
Following results were obtained from a consolidation test. Initial height of sample is 2.5cm and height of solid particles is 1.25cm.
advanced geotechnical engineering updated 4.7 years ago by teamques10 ★ 69k
0
votes
0
answers
992
views
0
answers
A pile of 450 mm diameter and 10.5m length is driven in a deposit having deposit having C=0, $\phi=30^{\circ}$, $\gamma=16.5kN/m^{3}$ and $\gamma_{sat}=18.5kN/m^{3}$.
advanced geotechnical engineering updated 2.8 years ago by Chandan15 • 300
0
votes
0
answers
899
views
0
answers
A cut has to be made 14m deep, inclined at an angle 45$^{\circ}$ to the horizontal.
advanced geotechnical engineering updated 4.7 years ago by teamques10 ★ 69k
0
votes
0
answers
2.1k
views
0
answers
A chimney with a rigid base 2.5 m square footing is placed at a depth of 1.2 m below the ground level.
advanced geotechnical engineering updated 4.7 years ago by teamques10 ★ 69k
1
vote
0
answers
837
views
0
answers
Given the following data from a consolidated undrained test with pure water pressure measurement determine the total and effective stress parameters.
advanced geotechnical engineering updated 4.7 years ago by teamques10 ★ 69k
0
votes
0
answers
1.1k
views
0
answers
A strip footing is to be designed for a given total load of 250 kN per m. Determine the width of strip footing by taking a factor of safety of 3 and use Terzaghi' bearing capacity equation.
advanced geotechnical engineering updated 4.7 years ago by teamques10 ★ 69k
0
votes
0
answers
947
views
0
answers
Calculate the ultimate bearing capacity of a rectangular footing 1.8m X 3.6m in plan founded at a depth of 1.6 m below ground level.
advanced geotechnical engineering updated 4.7 years ago by teamques10 ★ 69k
0
votes
0
answers
1.4k
views
0
answers
A granular soil has $\phi = 35^{\circ}$, $\gamma_{sat}$=19 kN/m$^{2}$. A slope has to be made of this material. If the factor of safety of 1.3 is needed against slope failure.
advanced geotechnical engineering updated 4.7 years ago by teamques10 ★ 69k
0
votes
0
answers
1.2k
views
0
answers
A square group of 25 piles of length 10m were embedded in stiff clay.
advanced geotechnical engineering updated 4.7 years ago by teamques10 ★ 69k
0
votes
0
answers
899
views
0
answers
In a failed soil slope of soft clay, the failure surface is circular and the centre of rotation is known.
advanced geotechnical engineering updated 4.7 years ago by teamques10 ★ 69k
<prev • 34 results • page 1 of 2 • next >